This topic has been archived. It cannot be replied.
-
枫下家园 / 电脑电信 / 用什么办法焊接这些特小的灯珠到电路板上去?
-xiaomh(DIY);
2021-12-3
{230}
(#14155191@0)
-
使用導電膠,粘住即可。
-888www888(HHH);
2021-12-3
(#14155535@0)
-
是不是ACF,, 要用hotbar压啊?这也许是唯一可行的方法,就是没找到用于LED的有关视频。看过导电胶用于cof
-xiaomh(DIY);
2021-12-3
(#14155586@0)
-
曾經這樣為CPU換過風扇。
-888www888(HHH);
2021-12-3
(#14156063@0)
-
先挤点焊锡膏再放上零件,焊。也可用普通焊锡丝先在板上点上两点,再用钳式焊头同时加热两点,再放入零件
-cocnut(tz);
2021-12-3
(#14155751@0)
-
直接焊,热风枪,好像都有难度。led 放在板子上,看不见金属部分
-xiaomh(DIY);
2021-12-3
(#14155776@0)
-
板子上刮刮,金属就出来了。这个LED已经很大了,大部分指示用的led小的和芝麻一样大
-cocnut(tz);
2021-12-3
(#14155874@0)
-
电路板上的焊点足够大,就是LED灯上的触点太小,放上去就几乎看不见了
-xiaomh(DIY);
2021-12-3
(#14156377@0)
-
if it is surface mount LED, it should be quite easy
-abcdefghi(9alphabetic);
2021-12-3
(#14155808@0)
-
用可以吸焊烯的枪,一般烙铁就可以。
-troyd(小C);
2021-12-3
(#14155851@0)
-
油管有视频教学,基本就是这样
-w4b(w4b);
2021-12-3
{517}
(#14155919@0)
-
这个虽小,但是还是比我要焊的LED大。一般电视,显示器的背光灯可以用这个方法。我想焊的是显示器的开关后面的指示灯,LED放上去后看不见触点,感觉不好下手
-xiaomh(DIY);
2021-12-3
(#14156358@0)
-
我焊过led芯片,触点太小,不好焊,
-googlebot(bot);
2021-12-3
(#14156078@0)
-
最后有没有什么解决方法。应该有办法。自己动手前想看到成功的例子,减少失败的机会
-xiaomh(DIY);
2021-12-3
(#14156365@0)
-
用Gage 24的铜线,焊接到灯珠的两端,然后,再焊接铜线和电板上的焊点。有段时间,我是在显微镜下焊接SMT元件,1206的元件大小和你这个类似,基本是直接烙铁手焊。
-zx1123(123);
2021-12-3
(#14156615@0)
-
PCB的soldering pads上先焊点锡上去,然后拿热风枪吹到融化,趁还没凝固赶快用镊子把LED放上去,模拟一下贴片机呗。
-honeylager(No Name);
2021-12-3
(#14156636@0)
-
太小了,不好控制,感觉难度有点大
-xiaomh(DIY);
2021-12-3
(#14156804@0)
-
这好像是最好的方法了,还要注意控制温度,SMT led很容易受热损坏。
-projects(pj);
2021-12-3
(#14156831@0)
-
烙铁比较难,估计热风枪比较容易。也要焊个0603的电容到电脑版,没有专业工具,烙铁试了不行,油管上的视频看着容易,操作起来难,准备搞个热风枪试试。
-yaya99(yaya);
2021-12-4
(#14157135@0)
-
我有电烙铁焊0805的电容到主板上的成功经历,很小但是可以做,0603更小,还是可以试试。使用热风枪,如果周围有很多小元件,需要注意保护,否则风险较大。电烙铁焊特小的元件难度较大,不容易控制位置,但是操作相对安全。
-xiaomh(DIY);
2021-12-4
(#14157660@0)
-
前几年0402的我都可以直接拿电烙铁焊,现在眼睛不行了,要借助放大镜,但是直接肉眼焊0603还是没问题的
-honeylager(No Name);
2021-12-4
(#14157757@0)
-
0402绝对是高难。那些专业维修的都是在显微镜下作业,业余的偶尔为之,往往没有这玩意
-xiaomh(DIY);
2021-12-4
(#14157874@0)
-
油管上焊这些电容都是热风枪,管子很细,风力也不大,都是专门修笔记本电脑的,烙铁应该也可以,没练过的应该很难,试着在废板子练了一下,应该可以搞好,但不容易,不知道哪能焊只要不太贵。不行就只能自己焊了。
-yaya99(yaya);
2021-12-4
(#14159332@0)